Microstructure and deformation behavior of novel metal–ceramic laminated composites Ta/Ti3Al(Si)C2–TiC

Cover Page

Cite item

Full Text

Open Access Open Access
Restricted Access Access granted
Restricted Access Subscription Access

Abstract

New metal–ceramic laminated composites Ta/Ti3Al(Si)C2–TiC were obtained by spark plasma sintering. The samples were synthesized at a temperature of 1250°C and a pressure of 50 MPa for 5 min. For the formation of composites, preceramic paper with a powder filler based on the MAX phase Ti3Al(Si)C2, as well as and metal foils made of tantalum, were used. The phase composition, microstructure and elemental composition were analyzed by X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectroscopy, respectively. It was found that as a result of sintering, dense multilayer composites were formed, consisting of tantalum metal layers, ceramic layers containing Ti3Al(Si)C2, TiC and Al2O3 phases, as well as reaction layers ~13 μm thick at the metal–ceramic interface, enriched with Ta, Al and Si. Based on mechanical test data, the ultimate bending strength of the obtained composites was determined (σbs = ~430 MPa). Metal–ceramic laminated composites with a refractory tantalum layer were shown to exhibit a ductile fracture mechanism, accompanied by a more than fourfold increase in absolute deformation compared to a Ti3Al(Si)C2-based ceramic composite. This is achieved due to deflection, branching of cracks at the metal–ceramic interface and plastic deformation of tantalum layers.

Full Text

Restricted Access

About the authors

A. V. Abdulmenova

National Research Tomsk Polytechnic University

Author for correspondence.
Email: ava75@tpu.ru
Russian Federation, Tomsk, 634050

E. B. Kashkarov

National Research Tomsk Polytechnic University

Email: egor_kashkarov@mail.ru
Russian Federation, Tomsk, 634050

D. G. Krotkevich

National Research Tomsk Polytechnic University

Email: ava75@tpu.ru
Russian Federation, Tomsk, 634050

N. Travitzky

Friedrich-Alexander-Universitat Erlangen–Nürnberg

Email: ava75@tpu.ru

Department of Materials Science, Glass and Ceramics

Germany, Erlangen, 91054

References

  1. Medvedovski E. // Wear. 2001. V. 249. № 9. P. 821. https://doi.org/10.1016/S0043-1648(01)00820-1
  2. Joshua P. // Mechanical Properties of Ceramics. Canada: Springer, 2014. P. 782. https://doi.org/10.1007/978-3-319-04492-7
  3. Munz D., Fett T. // Ceramics: Mechanical Properties, Failure Behaviour, Materials Selection. New York: Springer, 1999. P. 299. https://doi.org/10.1007/978-3-642-58407-7
  4. Shvydyuk K.O., Nunes-Pereira J., Rodrigues F.F., Silva A.P. // Ceramics. 2023. V. 6. P. 195. https://doi.org/10.3390/ceramics6010012
  5. Cramer C.L., Ionescu E., Graczyk-Zajac M., Nelson A.T., Katoh Y., Haslam J.J., Wondraczek L., Aguirre T.G., LeBlanc S., Wang H., Masoudi M., Tegeler E., Riedel R., Colombo R., Minary-Jolandan M. // J. Eur. Ceram. Soc. 2022. V. 42. № 7. P. 3049. https://doi.org/10.1016/j.jeurceramsoc.2022.01.058
  6. Chen X., Bei G. // Materials. 2017. V. 10. P. 366. https://doi.org/10.3390/ma10040366
  7. Sun Z.M. // Int. Mater. Rev. 2011. V. 56. № 3. P. 143. https://doi.org/10.1179/1743280410Y.0000000001
  8. Eklund P., Beckers M., Jansson U., Högberg H., Hultman L. // Thin Solid Films. 2010. V. 518. № 8. P. 1851. https://doi.org/10.1016/j.tsf.2009.07.184
  9. Lei X., Lin N. // Crit. Rev. Solid State Mater. Sci. 2022. V. 47. № 5. P. 736. https://doi.org/10.1080/10408436.2021.1966384
  10. Barsoum M.W., Radovic M. // Annu. Rev. 2011. V. 41. P. 195. https://doi.org/10.1146/annurev-matsci-062910100448
  11. Hadi M.A. // J. Phys. Chem. Solids. 2020. V. 138. P. 109275. https://doi.org/10.1016/j.jpcs.2019.109275
  12. Gonzalez-Julian J. // J. Am. Ceram. Soc. 2021. V. 104. № 2. P. 659. https://doi.org/10.1111/jace.17544
  13. Basu S., Obando N., Gowdy A., Karaman I., Radovic M. // J. Electrochem. Soc. 2011. V. 159. № 2. P. 90. https://doi.org/10.1149/2.052202jes
  14. Li X., Xie X., Gonzalez-Julian J., Malzbender J., Yang R. // J. Eur. Ceram. Soc. 2020. V. 40. № 15. P. 5258. https://doi.org/10.1016/j.jeurceramsoc.2020.07.043
  15. Сорокин О.Ю., Кузнецов Б.Ю., Лунегова Ю.В., Ерасов В.С. // Композиционные материалы. 2020. Т. 88. № 4–5. С. 42. https://doi.org/10.18577/2307-6046-2020-0-45-42-53
  16. Xie X., Yang R., Cui Y., Jia Q., Bai C. // J. Mater. Sci. Technol. 2020. V. 38. P. 86. https://doi.org/10.1016/j.jmst.2019.05.070
  17. Luo Y.M., Li S.Q., Chen J., Wang R.G., Li J.Q., Pan W. // J. Am. Ceram. Soc. 2002. V. 85. № 12. P. 3099. https://doi.org/10.1111/j.1151-2916.2002.tb00589.x
  18. Lagos M.A., Pellegrini C., Agote I., Azurmendi N., Barcena J., Parco M., Silvestroni L., Zoli L., Sciti D. // J. Eur. Ceram. Soc. 2019. V. 39. № 9. P. 2824. https://doi.org/10.1016/j.jeurceramsoc.2019.03.037
  19. He G., Xu J., Zhang Z., Qian Y., Zuo J., Li M., Liu C. // Mater. Sci. Eng. A. 2021. V. 827. P. 142069. https://doi.org/10.1016/j.msea.2021.142069
  20. Ashby M.F., Cebon D. // J. Phys. IV France. 1993. V. 3. № 7. P. 1. https://doi.org/10.1051/jp4:1993701
  21. Wu C., Wang Z., Li Q., Shi G. // J. Asian Ceram. Soc. 2014. V. 2. № 4. P. 322. https://doi.org/10.1016/j.jascer.2014.07.007
  22. Kashkarov E.B., Krotkevich D.G., Abdulmenova A.V., Ivashutenko A.S., Perevislov S.N., Lider A.M., Travitzky N. // Materialia. 2023. V. 27. P. 101673. https://doi.org/10.1016/j.mtla.2023.101673
  23. Kashkarov E.B., Abdulmenova A.V., Pushilina N.S., Syrtanov M.S., Mingazova Y.R., Nassyrbayev A., Krotkevich D.G., Travitzky N.A. // J. Alloys Compd. 2024. V. 982. P. 173848. https://doi.org/10.1016/j.jallcom.2024.173848
  24. Chen W.S., Ho H.J., Lin K.Y. // Materials. 2019. V. 12. P. 1220. https://doi.org/10.3390/ma12081220
  25. Laing M. // J. Chem. Educ. 2001. V. 78. № 8. P. 1054. https://doi.org/10.1021/ed078p1054
  26. Lunk H.J., Hartl H. // ChemTexts. 2019. V. 5. № 3. P. 1. https://doi.org/10.1007/s40828-019-0088-1
  27. Krotkevich D.G., Kashkarov E.B., Syrtanov M.S., Murashkina T.L., Lider A.M., Schmiedeke S., Travitzky N. // Ceram. Int. 2021. V. 47. № 9. P. 12221. https://doi.org/10.1016/j.ceramint.2021.01.070
  28. Sun X., Han W., Liu Q., Hu P., Hong C. // Mater. Des. 2010. V. 31. № 9. P. 4427.
  29. Knabl W., Leichtfried G., Stickler R. // Refractory Metals and Refractory Metal Alloys. Switzerland: Springer Nature, 2018. P. 307. https://doi.org/10.1007/978-3-319-69743-7

Supplementary files

Supplementary Files
Action
1. JATS XML
2. Fig. 1. Diffraction patterns of pre-ceramic paper (1) and the cross-section of the sintered laminated Ta/TAC–TiC composite (2).

Download (18KB)
3. Fig. 2. SEM image of the cross-section of the laminated Ta/TAC–TiC composite. RS – reaction layer.

Download (24KB)
4. Fig. 3. SEM image and corresponding distribution maps of reaction layer elements.

Download (57KB)
5. Fig. 4. Stress-strain curves of a monolithic TAC sample (1) and a laminated Ta/TAC–TiC composite (2).

Download (14KB)
6. Fig. 5. SEM images of the cross-section of the fracture surface (a) and the crack propagation region in the laminated Ta/TAC–TiC composite (b).

Download (40KB)

Copyright (c) 2024 Russian Academy of Sciences