Email this article 
The analysis of innovative manufacturing method of complete removable dentures
- Authors: Terekhov M.S.1, Apresyan S.V.1, Stepanov A.G.1
-
Affiliations:
- Peoples’ Friendship University of Russia
- Issue: Vol 27, No 3 (2023)
- Pages: 211-217
- Section: Experimental and Theoretical Investigation
- URL: https://rjdentistry.com/1728-2802/article/view/114752
- DOI: https://doi.org/10.17816/dent114752
- ID: 114752
Cite item
Open Access
Access granted
Abstract
BACKGROUND: The optimization of the digital protocol in the manufacture of complete removable dentures to obtain milled dentures with design close to those modeled using computer-aided design and computer-aided manufacturing software is an urgent problem in dental prosthetics.
AIM: To analyze the manufacturing of complete removable dentures and demonstrate the results of in vitro studies of prostheses obtained according to the developed protocol using the Kravets verticulator and prostheses in which the bases are bonded to the teeth with resins of cold and hot polymerization.
MATERIALS AND METHODS: With digital technologies, using the proposed modernized Wieland Digital Denture (Ivoclar Vivadent) protocol, 10 bases and 10 corresponding dentitions were obtained by milling, according to pre-made templates obtained using 3D printing. Then, five samples were bonded with cold cure resin using the verticulator, and five samples were made with hot cure resin and verticulator.
RESULTS: On most of the tooth treated with hot cure resin, the interlayer between the structures of the base and dentition was not observed, or interlayers had a thickness of 80±4 microns. The thickness of the interlayer of the cold curing specimens was 273±25 microns. Pores are not observed for plastic bonded specimens, both cold and hot cured.
CONCLUSION: The proposed method allows the use of digital technologies to obtain a monolithic plastic prosthesis, which eliminates inaccuracies in tooth positioning, during placement in the base of the prosthesis, and bind the base of the prosthesis and teeth using hot-curing acrylic plastic.
Full Text
About the authors
Matvei S. Terekhov
Peoples’ Friendship University of Russia
Author for correspondence.
Email: matter25@mail.ru
ORCID iD: 0000-0003-3498-0855
SPIN-code: 7472-9031
Postgraduate Student
Russian Federation, MoscowSamvel V. Apresyan
Peoples’ Friendship University of Russia
Email: dr.apresyan@gmail.com
ORCID iD: 0000-0002-3281-707X
SPIN-code: 6317-9002
MD, Dr. Sci. (Med.), Professor
Russian Federation, MoscowAleksandr G. Stepanov
Peoples’ Friendship University of Russia
Email: stepanovmd@list.ru
ORCID iD: 0000-0002-6543-0998
SPIN-code: 5848-6077
MD, Dr. Sci. (Med.), Professor
Russian Federation, MoscowReferences
- Apresyan SV. Digital planning of orthopedic dental treatment. Russian Journal of Dentistry. 2019;23(3–4):158–164. (In Russ). doi: 10.18821/1728-2802-2019-23-3-4-158-164
- Apresyan SV, Stepanov AG, Antonik MM, et al. Kompleksnoe tsifrovoe planirovanie stomatologicheskogo lecheniya (prakticheskoe rukovodstvo). Apresyan SV, editor. Moscow: Mozartika; 2020. (In Russ).
- Han W, Li Y, Zhang Y, et al. Design and fabrication of complete dentures using CAD/CAM technology. Medicine. 2017;96(1):e5435. doi: 10.1097/md.0000000000005435
- Steinmassl P-A, Klaunzer F, Steinmassl O, et al. Evaluation of currently available CAD/CAM denture systems. Int J Prosthodont. 2017;30(2):116–122. doi: 10.11607/ijp.5031
- Srinivasan M, Gjengedal M, Cattani-Lorente M, et al. CAD/CAM milled complete removable dental prostheses: An in vitro evaluation of biocompatibility, mechanical properties, and surface roughness. Dent Mater J. 2018;37(4):526–533. doi: 10.4012/dmj.2017-207
- Kalberer N, Mehl A, Schimmel M, et al. CAD-CAM milled versus rapidly prototyped (3D-printed) complete dentures: An in vitro evaluation of trueness. J Prosthet Dent. 2019;121(4):637–643. doi: 10.1016/j.prosdent.2018.09.001
- Radford DR, Juszczyk AS, Clark RK. The bond between acrylic resin denture teeth and the denture base: recommendations for best practice. Br Dent J. 2014;216(4):165–167. doi: 10.1038/sj.bdj.2014.99
- Clements JL, Tantbirojn D, Versluis A, Cagna DR. Do denture processing techniques affect the mechanical properties of denture teeth? J Prosthet Dent. 2018;120(2):246–251. doi: 10.1016/j.prosdent.2017.10.025
- Goodacre BJ, Goodacre CJ, Baba NZ, Kattadiyil MT. Comparison of denture tooth movement between CAD-CAM and conventional fabrication techniques. J Prosthet Dent. 2018;119(1):108–115. doi: 10.1016/j.prosdent.2017.02.009
- Tan HK, Brudvik JS, Nicholls JI, Smith DE. Adaptation of a visible light-cured denture base material. J Prosthet Dent. 1989;61(3):326–331. doi: 10.1016/0022-3913(89)90138-8
- Jung S, Park C, Yang H-S, et al. Comparison of different impression techniques for edentulous jaws using three-dimensional analysis. J Adv Prosthodont. 2019;11(3):179–186. doi: 10.4047/jap.2019.11.3.179
- Hirayama H. Digital removable complete denture (DRCD). In: Tamimi F, Hirayama H, editors. Digital restorative dentistry. Cham: Springer; 2019. P. 115–136.
- Meneghihi A, Mazzarella S, Di Franco A. Full upper and lower duplicate dentures using Vertysystem Furbo. Australasian Dentist. 2019:82–84.
- Patent RUS № 2722458/ 06.01.20. Byul. № 16. Apresyan SV, Kravets PL. Ustroistvo dlya izgotovleniya zubnykh protezov.
- Patent RUS № 2721891/ 05.25.20. Byul. № 15. Apresyan SV, Kravets PL, Stepanov AG, Terekhov MS. Sposob izgotovleniya s”emnykh zubnykh protezov.
Supplementary files
